|
|
|
Who's Online
There currently are 5934 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
very good manual with clear electrical schemes. Very helpful to find wat was wrong inside my microwave.
 ;
Hi, thankyou for providing the Nordmende Globetrotter original manufacturer's repair manual. Quality is very good and sharp - the PDF file was comfortably small to download. The only question is: why did it take so long to become ready for download?? Many thanks anyway, I fixed the fault in the radio thanks to the circuit.
regards: Nick
;
This was super service.Ordered this manual and was reading the download an hour later
;
as always, rapid and efficient, very good and clear prints
details clearly visible keep going this way!!!!!!
;
I expect a wonderful result as alaways!!!!!!
Usually is much faster....
Clarion Co., Ltd.
50 Kamitoda, Toda-shi, Saitama 335-8511 Japan Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703
Published by Service Dept. 298-6023-01 Jan.2005 Printed in Japan
Service Manual
NISSAN Automobile Genuine Satellite Tuner
Model
EN-1187E
After Serial No.0027925 (Genuine No.28051 CR900)
ORIGINAL SERVICE MANUAL
After Serial No.0027925 of this model, please confirm that and correspond to the original manual. This additional service manual is designed to be used together with Original model. Original model EN-1187E-A Manual No. 298-6023-00
DIFFERENCE FROM ORIGINAL MODEL
1. Change of the System Controller IC 2. Additional of the deatails of IC explanation 3. Additional of the Label(Software version code) 4. Change of the components
4. 4-1. 4-2. 4-3. 4-4. 5. 5-1. 5-2. 5-3. 6. 6-1.
Parts bag Mounting bracket Tap screw D-sems-hex-bolt Hex flange bolt Parts bag Insulok tie Corrugate tube Bonding wire Parts bag Black tape
----------300-7362-03 704-5010-81 734-4008-31 782-6016-00 ----------335-3847-00 825-1179-01 840-0539-00 ----------348-0334-00
2 4 4 1 4 1 1 2
To engineers in charge of repair or inspection of our products.
Before repair or inspection, make sure to follow the instructions so that customers and Engineers in charge of repair or inspection can avoid suffering any risk or injury.
1. Use specified parts. The system uses parts with special safety features against fire and voltage. Use only parts with equivalent characteristics when replacing them. The use of unspecified parts shall be regarded as remodeling for which we shall not be liable. The onus of product liability (PL) shall not be our responsibility in cases where an accident or failure is as a result of unspecified parts being used.
NOTES
* We cannot supply PWB with component parts in principle. When a circuit on PWB has failure, please repair it by component parts base. Parts which are not mentioned in service manual are not supplied. Specifications and design are subject to change without notice for further improvement.
*
COMPONENTS
EN-1187E-A
1. 2. 3. 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. Main unit Clamp Parts bag Edge protector Seal rubber Urethane sheet Spacer Magic tape Magic tape Protect seal ----------321-1026-00 ----------345-5247-00 345-5252-00 345-7010-00 345-8276-00 348-0105-02 348-0106-02 348-0333-00 1 4 1 2 14 1 2 2 4
2. Place the parts and wiring back in their original positions after replacement or re-wiring. For proper circuit construction, use of insulation tubes, bonding,gaps to PWB, etc, is involved. The wiring connection and routing to the PWB are specially planned using clamps to keep away from heated and high voltage parts. Ensure that they are placed back in their original positions after repair or inspection. If extended damage is caused due to negligence during repair, the legal responsibility shall be with the repairing company.
-1-
EN-1187E
|
|
|
> |
|
